Search

In Stock

Jaeger’s Surface Tension Apparatus

Integrated Manometric System: Features a premium borosilicate glass U-tube manometer and an aspirator bottle equipped with a fine-control stopcock for precise air-flow regulation and bubble formation frequency.

Modular Support Frame: Mounted on a chemically resistant, reinforced laboratory stand with adjustable clamps to maintain strict vertical alignment of the capillary tube and specimen vessel during sensitive measurements.

₹1,820.00

Quick Answer: The Jaeger’s Surface Tension Apparatus measures the surface tension of a liquid by the maximum bubble pressure method: air is pushed slowly through a narrow tube dipped in the liquid, and the greatest pressure reached before each bubble breaks away is read on a manometer. Because the tube sits in the liquid, the method is well suited to studying how surface tension changes with temperature.

The Maximum Bubble Pressure Method

A bubble growing at the tip of a fine tube is curved, and surface tension makes the pressure inside it greater than outside by 2T/r, where r is its radius of curvature. As the bubble grows, its radius first falls until the bubble is a hemisphere with the same radius as the tube, then increases again. The pressure therefore rises to a maximum at the hemisphere stage, after which the bubble breaks away. That maximum is what Jaeger’s method measures.

In the usual arrangement, water running slowly from an aspirator bottle drives air into the system at a steady rate, a manometer records the pressure, and the narrow tube dips to a measured depth h in the liquid under test. At breakaway, the manometer difference H balances the bubble pressure plus the hydrostatic pressure of the depth h, which gives T = (rg/2)(Hρ₀ – hρ), where ρ₀ is the density of the manometer liquid and ρ that of the test liquid.

Each bubble presents a small, fresh surface, and the tube can stay in a beaker warmed in a water bath, so readings at several temperatures are straightforward. The parts supplied with this listing, such as aspirator, manometer and tube, should be checked. The Quincke’s apparatus and Searle’s surface tension balance offer contrasting methods for comparison.

Specifications

Method Maximum bubble pressure (Jaeger’s method)
Pressure source Slow, steady flow from an aspirator
Measurement Manometer reading at the moment a bubble breaks away
Suits Surface tension at different temperatures
Parts supplied and tube bore Confirm at enquiry

Investigations

  • Measuring the surface tension of water and other liquids
  • Plotting surface tension against temperature as the liquid is warmed
  • Showing how soap, detergent or alcohol lowers surface tension
  • Comparing the result with a capillary rise measurement on the same liquid

Care & Handling

  • Set the aspirator so that bubbles form slowly, one every few seconds.
  • Keep the tube tip clean, round and free of chips; a damaged tip gives unsteady readings.
  • Check rubber connections for leaks before each session.
  • Handle glass parts with care and drain the manometer before storage.

Why Choose LabEquip

Undergraduate physics laboratories buy Jaeger’s apparatus because it is the standard route to the temperature variation of surface tension. LabEquip lists it in Physics Equipments; confirm the parts included through our contact page.

Frequently Asked Questions

Why is the maximum pressure used rather than any bubble pressure?

The pressure inside the bubble is greatest when the bubble is exactly hemispherical, with a radius equal to that of the tube. That radius is known, so the maximum pressure gives the surface tension directly.

Why must the bubbles form slowly?

The theory assumes the bubble is in equilibrium at every moment. Bubbles forced out quickly overshoot the true maximum and the manometer cannot follow them. Adjust the aspirator so that bubbles form at a slow, steady rate.

How is the effect of temperature studied?

Stand the beaker of liquid in a water bath, warm it in steps and repeat the maximum pressure reading at each temperature. Surface tension falls as temperature rises, which the readings show clearly for water.

Why is the depth of the tube in the liquid needed?

The air must also push back the liquid above the tube tip, so the manometer reading includes the hydrostatic pressure of that depth. Subtracting it leaves the pressure due to surface tension alone.

Which liquid is used in the manometer?

Usually water, sometimes coloured to make the levels easier to see. The pressures involved are small, and a low-density liquid gives a larger, more readable difference in levels.

What affects the accuracy of this method?

The tube radius must be known accurately and the tip must be clean, circular and cut square. Grease, chipped tips and air leaks in the rubber connections all lead to low or unsteady readings.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)